ENIAC Operating Manual
Written by Harry Fairhead   
Saturday, 08 June 2019

A look at the ENIAC Operating Manual, published 75 years ago this month, reveals just how difficult it was to program the world's first electronic general-purpose computer and how frustrating it must have been for its programmers.

When did you last read the operating manual of a computer, or any other electronic device for that matter? As programmers we tend to ignore any type of guidance, at least until something goes wrong and these days that rarely happens. But 75 years ago ENIAC's programmers probably did need to consult printed documentation to instruct them which switches to use and in which order. In this photo both Glen Beck and Betty Snyder, who are engaged in the task of programming ENIAC, appear to be holding documentation.

 Eniac prog

Source: US Army

The June 1946 Operating Manual, authored by Arthur W Berks and Harry D Huskey has been preserved for posterity and can be viewed here:

The majority of its almost 50 pages are drawings including ones of its floor-standing units:

eniacinitializingview

and others that show how it has to be programmed by positioning switches:eniscprog

Here we see Corporal Irwin Goldstein setting the switches on one of ENIAC's function tables:

eniacfuncprog

 It is the fact that ENIAC was programmed using switches that often causes people to claim that it wasn't really the first "programmable" computer.

The photo also indicates the size of ENIAC. One of its main innovations was the use of vacuum tubes, of which there were almost 18,000, which were inherently unreliable and required changing at frequent intervals.

tube

A vacuum tube - unreliable and expensive

Much of the text of the manual is devoted to safety concerns and while some of read rather like "Don't run with scissors" it does shed light on how trouble was anticipated. Here are some choice excerpts:

If ENIAC shuts down from overheating do not try to restart; call maintenance personnel. If any panel runs consistently much hotter than the others, do the same,

Do not remove any covers, front or back.

Do not open d-c fuse cabinet with the d-c power turned on. This not only exposes a person to voltage differences of around 1500 volts but the person may be burned by flying pieces of molten fuse wire in case a fuse should blow.

Do not pull directly on wire or cable; always use the plug case as a grip. 

Do not pound or force plugs.

Do not force any switches. 

In case you think the 1500 volts is quoted to scare the operators, it is worth recalling that vacuum tubes usually worked at voltages starting at  200V, which is a lot compared to the 3V today's processors work at. Another factor would have been the amount of heat produced. Each tube had a heater which caused the cathode to glow red hot. It would have been hot work without air con.

ENIACinuse

These days as soon as any piece of electronic equipment starts to malfunction there's the temptation not to fix it but to replace it - the replacement will probably by more powerful, will work faster, cost less and use less power or have longer battery life.

Compare this scenario to that of 75 years ago when the original ENIAC ran for 10 years.

More Information

ENIAC Operating Manual Jun46 (pdf) 

Related Articles

On This Day in 1946 - Eniac Unveiled 

Eckert & Mauchley and ENIAC

ENIAC Returns To Fort Sill 

To be informed about new articles on I Programmer, sign up for our weekly newsletter, subscribe to the RSS feed and follow us on Twitter, Facebook or Linkedin.

Banner


Visual Studio 17.9 Now Generally Available
18/03/2024

Visual Studio 17.9 is now fully available with AI assistance and better extensibility. The first preview of 17.10 has also been made available in preview.



AWS Adds Support For Llama2 And Mistral To SageMaker Canvas
12/03/2024

As part of its effort to enable its customers to use generative AI for tasks such as content generation and summarization, Amazon has added these state of the art LLMs to SageMaker Canvas.


More News

raspberry pi books

 

Comments




or email your comment to: comments@i-programmer.info

 

Last Updated ( Saturday, 08 June 2019 )